Top information

ASTM B 733 | Mil

Class 1 is for electroless nickel coatings that require no heat treatment Class 6 requires heat treatment of 300-320°C for at least one hour to improve coating adhesion Classes 2 through 5 exist at various levels between these two extrem , ASTM B733 Service Condition & Type , Type II requires 1-3% phosphorous content, which provides ....

Machining and Heat Treating ASTM A

Jul 19, 2011· If you order ASTM A-532 class III type A from the foundry, it will be annealed to about 400 bn As cast, it's about 450 bn We heat treat in a vacuum furnace with a forced air quench and get about 600 bn As far as being able to harden just portions of the part, not that I'm aware of...

Electroless Nickel Plating per MIL

Class 1: As-deposited, no heat treatment Class 2: Heat treatment at 260 to 400°C (500-752°F) to produce a minimum hardness of 850 HK100 Class 3: Heat treatment at 180 to 200°C (356-392°F) for 2 to 4-hr to improve coating adhesion on steel and to provide for hydrogen embrittlement relief...

heat treating astm a 532 class ii type d

Special heat-treatment process: Aiming at Cr-Mo alloy steel castings with higher hardness & higher impact value & even hardness , ASTM A532 Class III type A 25% Cr ASTM A532Class II type B 15% Cr-Mo , ASTM A 532 1-A,B,C,D Get Price...

Heat Treating of High

An austenitizing heat treatment usually comprised heating at temperatures between 750 and 790°C (1380 and 1450°F) with a soak time of 8 h Air or furnace cooling, not over 30°C/h, was conducted followed by a tempering/stress-relief heat treatment Refrigeration heat treatment is the more commonly practiced remedy for low hardness today...

Standard Specification for Abrasion

Heat treatment shall be done The chemical composition of a class and type (that is, Class I, Type A) shall conform to the range of values specified for carbon, manganese, silicon, nickel, chromium, molybdenum, copper, phosphorus, and sulfur Hardness test shall also be made This abstract is a brief summary of the referenced standard...

ASTM Welding Procedures A410 to A643

When using the low hydrogen electrodes, the pre and post heat treatment recommendations are frequently reduced or eliminated, however from a weld quality perspective always ensure that the weld locations are dry, the base metal is over 60 F, and that rust and mill scale is removed from the weld area...

AMS 2750 E, NADCAP, CQI

Furnace Class and Instrumentation Requirements of the AMS 2750 E Depending on the quality requirements of heat treatment job the customer specifies instrumentation type and the temperature uniformity class The instrumentation type describes the necessary combination of the applied control, recording media as well as thermocoupl...

Heat Treating HSS

Heat Treating In practice, post-production heat treatment is an available finishing option with two of the above manufacturing standards: ASTM A1085 and CSA G40 Some HSS production plants have the ability to perform heat treatment on site, but usually it involves transportation of the HSS to a third-party heat-treating facility...

GENERAL INFORMATION INFORMATIONGENERAL

GENERAL INFORMATION GENERAL INFORMATION , ASTM-A-276 Stainless and Heat Resisting Steel Bars and Shapes 302 309 316-L 403 304 310 317 410 , Type 631-17-7 PH Type XM-13-PH 13-8 Type 634-AM-355 ASTM-A-565 422 (Grade 616) ASTM-A-582 Free Machining Stainless and Heat ,...

astm a532 class3 type a

ASTM A532 Class III Type A magnetic properties , for MP NDT ASTM A532 Class II Type A 12% Cr High Chrome Wear Iron Plates EB20022 Wear Plates for Shot Blast Machines, Chutes, Clinker Silo,Port Machinery and Ball Mills This specification covers a group of white cast irons that have been alloyed to secure high resistance to abrasive wear in the applications of the mining, milling, earth ....

ASTM A532 Class I Type A | Ni

Jun 15, 2016· ASTM A532 Class I Type A or Ni-Hard 1 is an abrasion resistant high chrome white iron good for low or medium dynamic stress Read our data sheet today...

Heat Treating Guide

during heat treating processes are predictable with minimal distortion when compared to most grades of plain carbon steel The guidelines for the various types of heat treating apply to standard Dura-Bar grades of gray and ductile iron Methods and Cycle Times The following cycles are guidelines for each of the most commonly used heat treat ....

ASTM A234/A234M

732Fittings of Grades WP1 , WP12 , Class 1 , or WP12 heat treatment at 1200 °F [650 °C] instead of the heat treatment specified in 731 733 Fittings in all thickness produced by fusion welding after heat treatment specified in 731 shall be post-weld heat treated at a temperature not less than...

List of ASTM International standards

This is a list of ASTM International standards Standard designations usually consist of a letter prefix and a sequentially assigned number This may optionally be followed by a dash and the last two digits of the year in which the standard was adopted...

PLATING SPECIFICATIONS

ZYCI PLATING SPECIFICATIONS - GENERAL INFORMATION Page 3 Reference Only April 2018 ANODIZE, HARD MIL-A-8625 TYPE III Coating for aluminum Color will vary from light tan to black depending on alloy and thickness...

Metallurgical Aspects of HIGH

ii) When conditions of repeated impact are anticipated, the lower-carbon alloys, class I type B (Ni-Hard 2), are recommended because they have lesscarbideand,therefore,greatertoughness iii) A special grade, class I type C, has been developed for producing grindingballsandslugsHerethenickel-chromiumalloycompositionhas...

Finishing Specifications

Shown below is a list of basic specifications used in the Metal Finishing Industry It is in no way comprehensive, and is shown for reference purposes only...

ASTM Welding Procedures A36 to A930

Also even when heat treatment is not used its frequently beneficial to not allow the multi-pass inter-pass weld temperatures to exceed 200F If you ignore the heat treat requirements as recommended by the metal specifications ensure you use low hydrogen electrodes then, (a) Establish the welding procedure (b) Qualify the weld and HAZ properti...

All Metals Standards

All Metals Standards Search within Metals A1-00(2018): , Standard Guide for Qualification and Control of Induction Heat Treating A1101-16: Standard Specification for Sintered and Fully Dense Neodymium Iron Boron , Standard Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications...

No.416 Jianye Road, South Jinqiao Area,Pudong New Area, Shanghai, China.

Telephone : +86-21-58386189, 58386176

FAX : +86-21-58385681